Wind turbines turn moving air into clean electricity with no fuel and no operating emissions. We assess wind sites, develop onshore and offshore projects, and integrate them with solar and storage into complete systems.
Wind has become one of the world's largest sources of renewable electricity. Wind farms now operate on land and at sea, ranging from single turbines serving one facility to large farms supplying national grids.
Its value lies in a free, renewable fuel, no emissions or water use during operation, and a natural fit with solar power — in many places the wind blows at night and in the seasons when sunshine is weaker.
But a wind project succeeds long before a turbine is chosen: through careful measurement of the wind resource, a study of the site and its constraints, planning of the grid connection, and an assessment of the impact on the surroundings and wildlife.
Onshore and offshore wind farms
Each has its own advantages and requirements; the right choice depends on the site, the wind resource and the available infrastructure.
Illustrative image
Onshore wind farms
Turbines built on land — on open plains, uplands and coastal areas. They are easier to reach and relatively cheaper to build and maintain, and farming or grazing can usually continue on the land between turbines.
Simpler, relatively lower-cost construction and maintenance
Flexible scale, from a single turbine to a large farm
Closer to transmission networks and roads
Requires appropriate distances from homes
Illustrative image
Offshore wind farms
Turbines built at sea on fixed foundations in shallower water or on floating platforms in deeper water. They usually benefit from stronger, steadier winds and allow larger turbines far from populated areas.
Usually stronger, more consistent winds
Larger turbines and higher capacity per unit
Greater logistical challenges and installation and maintenance costs
Subsea cables and substations bring power ashore
A general comparison of onshore and offshore wind farms
Item
Onshore
Offshore
Foundations
Concrete foundations on land
Monopile, jacket or floating
Maintenance access
By road
By vessel or helicopter, depending on sea state
Grid connection
Overhead or buried lines to a substation
Subsea cables, often with an offshore substation
Timeframe
Usually shorter
Longer due to marine complexity
Environmental focus
Wildlife, noise and land use
Marine life, birds, shipping and fishing
How do wind turbines generate electricity?
Pick a stage to follow energy from moving air to the grid or storage.
Moving air
Wind carries kinetic energy proportional to the cube of its speed. That is why turbines are placed on open, elevated sites where the wind is stronger and steadier, with rotors raised on tall towers away from turbulent air near the ground.
Doubling wind speed gives roughly eight times the power
Height brings stronger, smoother wind
Main turbine components
Blades
Usually made of light, strong composite materials and shaped aerodynamically to capture wind energy.
Hub and pitch system
Holds the blades and adjusts their angle to control power and protect against high winds.
Nacelle
Houses the main shaft, gearbox, generator, and cooling and control systems.
Gearbox or direct drive
Raises rotational speed before the generator, or is omitted in direct-drive designs.
Generator
Converts rotational motion into electricity.
Yaw system
Turns the nacelle to keep facing the wind.
Tower and foundation
Raise the rotor to a better height and carry the large wind loads.
Control and monitoring
Systems that track performance and shut the turbine down automatically when needed.
Wind resource assessment and site selection
Wind is the project's “fuel”, so measuring it accurately is the basis of every later decision.
01
Identify candidate sites
Review wind maps, terrain, infrastructure and regulatory constraints.
02
Measure the wind on site
Install met masts or LiDAR to record speed, direction and turbulence at several heights.
03
Analyse the data
Correlate measurements with long-term records to estimate typical wind behaviour over the years.
04
Estimate annual yield
Model the farm's output, accounting for losses and the turbines' effect on each other.
05
Study site constraints
Land, roads, grid proximity, homes, aviation and environment.
Illustrative image
Wind farm planning and technical feasibility
Good planning turns wind data into a project that can be built and stays stable over its life.
01
Layout design
Positioning turbines and spacing them to limit mutual wake effects.
02
Turbine class selection
Matching the turbine to site wind conditions under international standard classes.
03
Geotechnical studies
Investigating soil or seabed to design safe foundations.
04
Transport and installation
Planning the transport of long blades and towers, cranes and access roads.
05
Permits and environmental assessment
Securing approvals, impact studies and community consultation.
06
Economic model
Estimating costs, revenues, power-sale arrangements and financing.
Illustrative image
Grid connection and electricity distribution
Power from the turbines is collected through medium-voltage cables to the farm substation, where the voltage is raised for export to the grid. Offshore, subsea cables bring it ashore.
Because wind output varies, the farm must meet the grid operator's requirements for voltage and frequency control and fault response, and the grid may need reinforcement or storage to absorb the output.
Connection capacity studies and grid-operator requirements
Substation, protection and metering equipment
Control systems that support grid stability
Output forecasting for operational planning
Hybrid systems: wind + solar + storage
In many places wind and solar complement each other: the sun peaks by day and in summer, while the wind may be stronger at night or in winter. Storage adds flexibility that makes supply steadier.
Wind
Output that can continue at night and in cloudy weather, depending on the site.
Solar
Predictable daytime output that follows the sun.
Batteries
Store surplus and release it when output drops or demand peaks.
Illustrative image
Better use of the same grid connection point
Steadier supply for facilities and remote sites
Less reliance on fuel-fired generators
How well the sources complement each other depends on each site's wind and sunshine patterns and is assessed through measurement and simulation.
Turbines run for many years in demanding weather; regular maintenance is what keeps them performing and safe.
Remote monitoring
Supervisory systems track every turbine in real time and flag faults.
Condition monitoring
Vibration and temperature sensors detect early signs of wear in gearboxes and bearings.
Preventive maintenance
Scheduled inspections of mechanical and electrical parts.
Blade inspection
Visual and drone inspections to catch erosion and cracks early.
Spare-parts planning
Planning for large components and cranes to reduce downtime.
Safety at height
Rigorous training, equipment and procedures for work at height.
Environmental considerations
Wind power is clean in operation, but developing it responsibly means caring for the environment and nearby communities.
Wildlife
Studying bird and bat movements and designing and operating the farm to limit impact, including temporary curtailment during migration where needed.
Noise
Keeping safe distances from homes, meeting local noise limits and choosing quieter technologies.
Land use
A turbine occupies a small footprint, and farming and grazing can usually continue around it.
Visual impact and shadow flicker
Assessing the landscape view and moving blade shadows near inhabited areas.
End of life
Planning for decommissioning, site restoration and recycling components where possible.
Every project's environmental impact depends on its location and design, so it is established through environmental impact assessments and monitoring during operation — not general assumptions.
Benefits, limitations and industrial applications
Benefits
Electricity with no emissions during operation
A free, renewable fuel
No water consumption in operation
A good match with solar power
Shared land use with farming
Limitations
Variable output that depends on the wind
Requires sites with a good wind resource
Logistical challenges in moving large components
Needs sufficient grid connection capacity
Applications
Supplying national and regional grids
Powering large industrial facilities
Remote sites and islands, with storage
Hybrid systems with solar power
Potential support for future green-hydrogen projects
Frequently asked questions
What wind speed does a turbine need to operate?
Most modern turbines start generating at relatively low wind speeds, reach rated power at higher speeds, and shut down automatically in storms to protect themselves. Exact values vary by turbine model and are established in the site study.
Which is better: an onshore or an offshore wind farm?
There is no single answer. Onshore farms are simpler and cheaper to build and maintain, while offshore farms benefit from stronger, steadier winds and larger turbines but are more complex and costly. The choice depends on the site, the resource and the infrastructure.
How long should the wind be measured before a project?
On-site measurement over at least a full year is usually recommended to capture seasonal variation, with the data then correlated against long-term records to estimate output over the project's life.
Are wind turbines noisy?
Turbines produce aerodynamic and mechanical sound, so safe distances from homes are set according to local limits, and quieter technologies and designs are chosen. This is assessed in the environmental impact study.
What happens when the wind stops?
Output falls or pauses, which is why wind farms operate within a broader energy mix, are combined with solar and batteries, or rely on the grid to maintain supply when the wind drops.
Can wind be combined with solar in one project?
Yes — these are hybrid systems. The two sources often share the same connection point and complement each other in many places, with batteries adding further flexibility. How well they combine is assessed through measurement and simulation for each site.
How long does a wind turbine last?
Modern turbines are designed to operate for decades with regular maintenance, and some major components may need replacing during that time. Actual lifetime depends on site conditions and the quality of operation and maintenance.
Planning a wind energy project?
Share your project location and any available data on wind, land and grid connection, and we will help you identify the right assessment steps.